What should be paid attention to in the design of patterned alloy aluminum plate?

Aluminum alloy aluminum plate with fierce pattern: 3003 as the main raw material, also known as rust-resistant aluminum plate. Its strength is slightly higher than that of ordinary aluminum alloy diamond plate, and it has some rust resistance, but its hardness and corrosion resistance are lower than those of 5000 series diamond plate. Therefore, this product is suitable for the low rust resistance requirements of truck models and cold storage floors.

Patterned alloy aluminum plate

At present, with the development of the market, patterned alloy aluminum plates are more and more used in the market. Users' guarantee of its use results is welcome. When manufacturing aluminum plates, we need to pay attention to the design requirements. What should we pay attention to in the design?

1, pay attention to the design quality

In order to ensure the design quality of patterned alloy aluminum plate, increase design satisfaction, reduce design problems and ensure quality, it is necessary to pay attention to the design problems in the production of patterned aluminum plate to ensure quality.

2. Pay attention to the pattern display

In order to meet the requirements of graphic display in production, we should communicate with customers more, achieve the style required by customers, ensure to reduce the shortage of graphic display results, reduce the shortage of graphic display and ensure good results.

3. Pay attention to reasonable results

It is very important for patterned aluminum factory to pay attention to the rationality of the results, reduce the shortcomings, ensure normal production, reduce design defects and ensure the results.

Patterned alloy aluminum plate is mainly used in furniture. It is a modern material with high cost and various types. Commonly used in refrigerators, air conditioners, carriages, platforms, packaging pipes, screen skeletons, platform feet, decorative strips, handles, slot caps, chair tubes, etc.

The above is the introduction of matters needing attention in the design of patterned aluminum alloy plate, for your reference. Most manufacturers of patterned aluminum alloy plate are used in a variety of welded structural products, mainly because of its light weight, high strength, good corrosion resistance, non-magnetism, good formability and good low temperature performance.

Construction technology of patterned aluminum plate after entering the site

After the patterned aluminum plate enters the site, each fitting can be inspected, and then the structure can be constructed. A building is generally equipped with a set of patterned aluminum formwork system and three sets of support systems. The installation of wall column formwork is carried out after the steel bar binding of wall column is completed and the water and electricity pre-processing acceptance is passed. The main points of the table are: before installation, check whether the floor elevation of the installation device meets the requirements according to the elevation, and the higher part must be chiseled flat, and the lower part should be padded with wooden blocks under the aluminum mold to control the floor elevation error within 5mm; Before assembling the aluminum formwork, evenly brush the release agent on the inner side of the patterned aluminum formwork, and the release agent should not be too thick or missed; According to the serial number of the wall column template assembly drawing, first assemble one side of the wall column template, and connect the templates with pin pieces, then put on the opposite screw and put on the PVC pipe and plastic rubber ring, so as to facilitate the plugging of the screw hole, then tie the steel bar and fix the cement internal brace to determine the section size of the aluminum formwork after reinforcement, and finally assemble the other side of the patterned aluminum plate, and tighten the nut of the opposite screw to fix the wall column template.

After the wall column template installation is completed, install the beam template. According to the beam template assembly diagram, install the wall beam corner template, beam bottom template, beam bottom support upright post, beam side template, beam top corner template and wall top corner template in turn. The installation points are as follows:

The connection between patterned aluminum formwork adopts pin pieces, and the connection of components at corners adopts bolts to avoid the phenomenon of falling off and expanding formwork when pouring concrete; The supporting upright post at the bottom of the beam should be vertical without looseness. During the installation of the beam bottom formwork, the elevation of the beam bottom should be leveled one by one by using a laser leveler. After installing the corner formwork at the top of the beam and the top of the wall, the floor slab supporting Liang Li formwork should be installed in turn according to the pattern aluminum plate assembly diagram, and the formwork should be assembled in turn from one corner until the formwork is assembled as a whole. The support bar on the bottom of the floor aluminum plate support beam should be vertical and not loose.

Link-B2B is a professional supplier listing service platform which will provide high quality and trustworthy supplier list to international buyers. If you are looking for patterned alloy aluminum plate suppliers, feel free to visit Link-B2B.com and send a request.